Fork Cap Installation - Street
and a few Dirt Bikes
(XR400, CR85 & RM85)
or
"How to Make the Adjusters Have the Right Amount of Clicks"
Also includes How to Use Standard and Wall-Mounted Fork Spring Compressors There are two basic types of adjusting screws on street bike fork caps: 1) One that stops when you turn it in and 2) one that doesn't stop when you turn it in. To see which type you have you will need to have the cap off the damping rod. Back out the adjusting screw (counterclockwise) all the way until it stops. Attempt to screw it in 6 turns, (count turns as not all caps have clicks). If it stopped turning at 4 or 5 turns you have the type where the adjusting screw stops. If you are still turning and a tiny ball bearing and spring fall out, you've gone way too far. If this happens look in the waste oil pan you have sitting under the bench in the corner as that is where most things you drop end up. With both types of caps the procedure is almost the same. Click on the images to enlarge. |
| SUPPLIES
Contact Cleaner - or other good, clean solvent |
| |
| HOW TO CREATE THE CORRECT NUMBER OF CLICKS FA19- Make sure the Rebound Adjusting Screw is backed out all the way then screw it in 20 clicks. This step is important in setting the fork cap height as well as the proper number of clicks of adjustment. If there are no "clicks" back out the Adjusting Screw all the way then turn it in 5 turns. |
| FA20A - Mount the fork leg in the Spring Compressor. You can use either the Standard TFSC 01 Spring Compressor or the Wall Mounted version TFSC 02. The Pin on the Foot goes into the hole in the bottom of the fork. The Fork Spring Spacer has two holes in it near the top. Put the pins of the Spring Compressor into the holes and tighten the adjuster screw until both pins are fullycaptured by the hole. |
| FA20- This is TFSC 01 Standard Spring Compressor. Tighten the Spring Compressor but make sure you stop before the tool hits the top of the fork tube. Some people have tightened it so hard it breaks the tool! Please don't do this. Tightening the tool is best accomplished with an electric drill with a socket or a speed handle. Do not use an impact or it will destroy the tool. |
| FA21- Once the fork is compressed enough, extend the damping rod and remove the Bleeding Tool. Check that the Jam Nut is on all the way. This makes sure it is out of the way for now. |
| FA22- Install the Fork Cap. Make sure the Fork Spring Preload Adjuster is backed out all the way. |
| FA23- Screw it down until it gently seats the rebound needle. When the Cap is being screwed on to the Damping Rod the Rebound Adjuster Screw will eventually contact the Rebound Adjuster Rod. As you continue screwing the Cap on, the Rebound Needle will eventually contact the Seat and stop. DON'T FORCE IT!!! If you force it too tightly it will jam the Needle into the Seat and damage the seat... so be gentle. |
| FA24- Bring the jam nut up against the fork cap. |
| FA25- Back out the adjuster a few clicks to give the Needle clearance from the Seat while you... |
| FA26- tighten the Jam Nut. Check the number of Rebound Adjuster clicks that are available. There should be close to 20 clicks (or 5 turns) as that is what the procedure we use creates. If it is more than 2 clicks different than that remove the cap and repeat the procedure. |
| FA27- Unscrew the Fork Spring Compressor Tool, remove the fork leg from the tool, and tighten the Cap. Set all your adjusters, mount the forks on the bike, and enjoy. |
| FA28- TFSC 02 Wall Mounted Spring Compressor
Place the fork in a RT Fork Spring Compressor (TFSC 02) with the tool's top pins in the holes in the spring spacer and the locating pin in the bottom of the fork. |
| FA29 - Compress the fork spring. This pic is a little awkward. Normally you will stand in front of the tool and put your foot at right angle to the lever.
The rest is the same as TFSC01.
|